***環保型汽車底盤裝甲誠招省級***
河北省 江蘇省 上海市 北京市 安徽省 河南省 山西省 天津市 浙江省 遼寧省
招商電話15588610888 李經理
本公司研發的***新一代***大政牌環保型汽車底盤裝甲，是采用***的聚氨酯合成技術，由高分子聚氨酯彈性體合成的，***低氣味，對******無害，符合國際環保標準。我公司致力于打造中國底盤裝甲的***品牌，為您的愛車提供持久保護，提高行車安全。
The advanced chassis protection (Polymer polyurethane elastomer) of brand Da Zheng developed by our company adopts the Germany advanced PU synthetic technology; and the chassis protection synthesized by polymer polyurethane elastomer, no toxicity & low odor, meets the international environmental standa***. And the product can provide lasting protection for your car and improve your road safety.Leading level in domestic & overseas
高彈性 high elasticity
高附著力 high adhesion
阻燃防銹 flame & rust retardant
隔熱防寒 heat insulation & cold-proof
隔聲降噪 Noise reduction
防撞擊 Anti-collision
防震 anti-vibration
我司生產的底盤裝甲具備的優異性能大大優越于目前市場銷售的瀝青，橡塑類等汽車底盤裝甲產品，本公司生產的汽車底盤裝甲有效成分高，一次噴涂的裝甲厚度可達2mm，噴一次即可滿足所需要求。這樣大大降低了消費成本，提高工作效率。
The performance of the chassis produced in our company is greatly superior to the bituminous & rubber based products. The products we produced, with high content of active c***tituent, the spraying thickness can reach 2mm for one-time spraying, and one-time spraying can meet all your need. So the
c***umption can be reduced greatly and the work efficiency can also be
improved.
適用范圍
適用于各類車輛的底盤，輪弧，汽車大梁，油箱殼，葉子板內側，發送機罩，后備箱底部等。
Scope of application
It is applicable to the chassis of all kinds of vehicles, fender trim, automotive frame, tank shell, fender inside, tran***itter cover and bottom of trunk etc.
產品性能
本品在240度至-50度范圍內無變軟變脆現象，且本品耐熱，耐寒，耐潮濕，耐水泡，并可有效阻隔寒暑對車內溫度的影響，充分體現其優良的性能和強附著力；
另外，本品防銹能力***，且彈性強、韌性好、抗撕裂，可完全***砂石對車輛底盤的撞擊，大幅度降低輪胎與路面摩擦產生的噪音。
Product performance
In the temperature scope of 240~ -50°, the product without softening & brittleness phenomenon, and with good performances of heat resistance, cold resistant, moisture resistance, and blister resistance; it can impede the effect ( in- car temperature) caused by cold & heat effectively, which fully embodies the good performance and strong adhesion of the product; in addition, the product with excellent anti-rust capability, strong elasticity & toughness and highly tear resistant, which can completely resist the impaction on chassis from dinas and significantly reduce the noise caused by the friction between tyre & p***ement.
施涂說明
1. 噴涂前徹底清潔汽車底盤，去除銹跡，污漬，油脂，蠟質等。并覆蓋保護無需噴涂的部位。
2. 本聚氨酯彈性體，為濕固化高聚物。開瓶后表面有初固化膜。將噴槍直接插入罐中然后旋緊，充分搖勻，連接壓力為0.04mpa-0.06mpa壓縮空氣，然后即可噴涂。
3. 本品具有優良的觸變性，無滴掛現象；固化時間，春季 2-3小時；冬季6-8小時。夏季速干時間為15分鐘，15分鐘后，即可行車。冬季噴涂1小時后即可行車。完全固化時間為8-12小時，固化后，表面光滑無粘性。且具有強韌彈性。4. 噴涂完畢請用專用清洗劑將噴槍清洗干凈即可。
Application instruction
1. Before application, clean the automotive chassis completely to remove rust, dirty mark, grease and waxes etc.； and protect the area not to be sprayed.
2. The product is moisture curing polymer, which is with a layer of cured film on surface after opening. Insert spraying gun into the pot directly, tighten the pot and shake fully, then spray; the connection pressure is 0.04mpa-0.06mpa (compressed air).
3. The product is with good thixotropy, without sagging; the curing time is 2~3h in spring and 6~8h in winter. The quick drying time is 15mins in spring, and the car can be driven after 15 mins, and in summer, the car can be driven after 1 hour. The complete curing time of product is 8-12 h; after curing, the surface is ***ooth, without viscosity; and with good toughness & elasticity.
4. The spraying gun shall be cleaned with special cleaning agent after spraying.